Industrial Socket Price in Pakistan: 16 A and 32 A Types, 3-Pin and 5-Pin, IP44 Protection and Safe Wiring
Industrial socket price in Pakistan runs from about PKR 970 for a 16 A unit to PKR 1,270 for a 32 A surface-mounted socket, with weatherproof and three-phase types costing more. An industrial socket is a heavy-duty plug and socket for loads that a normal 13 A socket cannot carry, such as welding machines, compressors, pumps and generators. This page explains the types, the amp ratings, the IP protection classes, indicative rates and safe wiring. See also plugs and sockets and the changeover switch guide.
Where industrial sockets are used
Typical uses are workshops, welding sets, air compressors, water pumps, commercial kitchens, marriage halls, event power and generator outlets. The plug locks with a ring or a keyed shape so it cannot be pulled out by a tug on the cable, and the housing resists dust and splashes better than a domestic socket.
Types and ratings
- 16 A, 3-pin. Single-phase loads such as pumps and small machines.
- 32 A, 3-pin. Heavier single-phase loads such as welders and large pumps.
- 16 A or 32 A, 5-pin. Three-phase supplies for motors and large machines.
- Panel, surface and cable types. For fixed walls, for rough walls and for extension leads.
Industrial socket price in Pakistan
Rates depend on amp rating, poles, IP rating and brand. These indicative ranges show common retail figures.
| Item | Indicative range |
|---|---|
| 16 A 3-pin industrial socket, IP44 | PKR 970 - 1,070 |
| 32 A 3-pin surface socket | About PKR 1,270 |
| 16 or 32 A industrial plug | PKR 500 - 1,500 |
| 5-pin 16 A three-phase socket | PKR 2,500 - 6,000 |
| Weatherproof IP67 socket | PKR 3,500 - 9,000 |
| Branded industrial set, same rating | PKR 4,000 - 15,000 |
Prices move with brand, model, size and stock. Use these ranges to judge a quote, then compare the exact model and what is included.
IP protection classes
IP44 resists dust particles and splashes, which suits workshops and covered outdoor use. IP67 can survive temporary immersion and suits washdown areas and open sites. Choose the class for the place, not just the amps, and use a cover on any socket that stays outdoors.
Matching the socket to the load
Check the rated current of the machine and choose a socket with some margin. A welder or compressor may have a high start current, so use the correct breaker and cable. Do not plug a heavy machine into a 13 A socket or an extension board.
Generator and event use
For generator outlets use the correct plug and a changeover switch so the supply never back-feeds the grid. For events and marriage halls, use a weatherproof distribution box with industrial sockets rather than loose extension leads.
Maintenance and safety
Check the pins and the cable gland for heat marks, keep covers closed and clean dust from the socket. Replace a plug with a cracked body. A warm plug or socket means a loose connection or an overload, and should be fixed before the next use.
Frequently Asked Questions
A 16 A 3-pin industrial socket is about PKR 970 to 1,070 and a 32 A surface socket about PKR 1,270. Five-pin three-phase sockets cost about PKR 2,500 to 6,000 and weatherproof IP67 types more. Ask for the specification in writing so you can compare quotes on the same basis.
The number is the maximum current. A 16 A socket suits pumps and small machines, while a 32 A socket suits welders and large pumps. Choose a socket with margin for the load and match the cable and breaker. Check the warranty terms and who honours them before you pay.
IP44 means the housing resists solid objects larger than about one millimetre and splashing water. It suits workshops and covered outdoor use. For washdown areas or open sites, a higher class such as IP67 is better. Measure carefully and confirm sizes with the seller before ordering.
No. Heavy machines should have their own industrial socket and breaker. An extension board is not designed for welders, compressors or large pumps and can overheat under that load. Rates and stock change, so confirm the current position before you commit. If you are unsure, send a photo and the measurements and we will advise.
Only if the machine needs three-phase power. Check the nameplate. Three-phase sockets have five pins and need an MCCB or suitable breaker, and a licensed electrician should install them. If you are unsure, send a photo and the measurements and we will advise.
Message us on WhatsApp with what you need and where it will be used. We check what we can supply and send a written rate showing the model, quantity, warranty and delivery, so you can judge it against other offers. Rates and stock change, so confirm the current position before you commit.
Planning industrial power points?
Send the details and a photo. We reply with a written rate.