Corner Kitchen Sink Planning: Placing a Sink in an L-Shaped Corner, Angled and Straight Bowls, Cabinet Type, Tap Reach, Plumbing, Window and Storage Trade-Offs
A corner kitchen sink sits where two counters meet, using the awkward corner and often giving a view through a window, but it needs careful planning of the cabinet, the bowl, the tap reach and the plumbing. This page covers placing a sink in an L-shaped corner, angled and straight bowls, cabinet type, tap reach, plumbing, window and storage trade-offs. For sink types see double kitchen sinks, SS kitchen sinks and corner cabinets.
Why a corner sink
A corner sink uses the corner that is otherwise hard to use, frees the straight runs for counters and often sits under a corner window. It works well in L-shaped and U-shaped kitchens. The trade-off is a more complex cabinet and less usable storage below.
Types of corner sink
- Angled corner sink. A bowl set diagonally across the corner.
- Double bowl along one arm. A standard sink placed at one end near the corner.
- L-shaped sink. Bowls set at right angles.
- Corner round bowl. A single round bowl fitted into a corner.
Indicative rates
These ranges show common figures.
| Item | Indicative range |
|---|---|
| Standard double bowl sink | PKR 12,000 - 30,900 |
| Special corner or L-shaped sink | PKR 25,000 - 80,000 |
| Corner base cabinet with cut-out | PKR 15,000 - 40,000 |
| Counter cut-out, corner | PKR 2,000 - 8,000 |
| Plumber and fitting | PKR 1,500 - 5,000 |
Prices move with brand, model, size and stock. Use these ranges to judge a quote, then compare the exact model and what is included.
Cabinet and storage
An angled corner cabinet gives a wide opening but lots of dead space. A standard 36 inch base cabinet at the corner is simpler. Use baskets or a pull-out under the sink for cleaning supplies. See cabinet organizers.
Tap reach and clearance
Choose a swivel tap that reaches the bowl without hitting the wall or window. Leave space on both sides of the sink for drying and dish racks, at least 18 to 24 inches. Check that window frames clear the tap.
Plumbing
Plan water and waste points at the corner. If the sink moves from an old position, new pipes are needed. Waste pipes need a slope to the drain, so plan the route early. Fixed plumbing should be done by a licensed plumber.
Trade-offs
- Counter space. A corner sink can reduce the prep space near it.
- Work triangle. Check distances to the hob and fridge.
- Cost. Special sinks and cabinets cost more.
- Access. Two people may find the corner cramped.
Corner or straight
A straight sink along one counter is simpler and cheaper, with better access and storage. A corner sink suits kitchens where the corner is wasted and the window is there. Test both layouts with tape on the floor before deciding.
Before you decide
Mark the sink position and the clearances on the counter with tape, stand at it and mime washing. Check the work triangle, the tap reach and the cabinet door swing. A well planned corner sink makes use of space you would otherwise lose.
Frequently Asked Questions
A sink placed where two counters meet, often with a diagonal or L-shaped bowl, using the corner space. Ask for the specification in writing so you can compare quotes on the same basis. Check the warranty terms and who honours them before you pay.
A standard double bowl sink is about PKR 12,000 to 30,900, a special corner or L-shaped sink about PKR 25,000 to 80,000, plus a corner cabinet about PKR 15,000 to 40,000. Check the warranty terms and who honours them before you pay.
Less prep counter near the sink, a more complex cabinet and extra cost. Measure carefully and confirm sizes with the seller before ordering. Rates and stock change, so confirm the current position before you commit. If you are unsure, send a photo and the measurements and we will advise.
At least 18 to 24 inches on each side for drying and prep. Rates and stock change, so confirm the current position before you commit. If you are unsure, send a photo and the measurements and we will advise. Ask for the specification in writing so you can compare quotes on the same basis.
It depends. Corners suit kitchens with a corner window and wasted space, while straight sinks are simpler and cheaper. If you are unsure, send a photo and the measurements and we will advise. Ask for the specification in writing so you can compare quotes on the same basis.
Message us on WhatsApp with what you need and where it will be used. We check what we can supply and send a written rate showing the model, quantity, warranty and delivery, so you can judge it against other offers. Rates and stock change, so confirm the current position before you commit.
Placing a sink in the corner?
Send the details and a photo. We reply with a written rate.