Gate Design in Pakistan: Main Gate, Steel, Modern, Sliding and Walk-Through Styles
A good gate design does three jobs at once. It sets the first impression of the house, it keeps the plot secure, and it has to open easily every day for years. In Pakistan a plain iron double gate costs PKR 60,000 to 200,000, and the final figure depends on the metal, the size, the pattern and whether the gate is hand-swung or motorised. This page covers main gate, steel, modern, sliding and walk-through styles, with the finishes and checks that matter before you order. For the door behind the gate, see main door design.
Gate styles at a glance
Five styles cover almost every house in Pakistan. Pick by plot width, parking and how much privacy you want.
| Style | Best for | Opens by | Watch out for |
|---|---|---|---|
| Double-leaf swing gate | Plots with a clear drive-in space | Two hinged leaves | Needs swing room inside and outside |
| Single-leaf swing gate | Narrow plots and side entries | One hinged leaf | Heavy leaf sags at the hinge |
| Sliding gate | Tight frontage, busy road | Track or cantilever slide | Needs wall length equal to the opening |
| Folding gate | Shops and garages | Folds into stacks | Many moving parts to maintain |
| Walk-through gate | People entry beside a car gate | Small hinged leaf | Latch must suit the lock |
What a gate costs
These are typical rates in Pakistan for the gate itself. Fitting, pillars and electrics are quoted separately.
| Item | Rate (PKR) |
|---|---|
| Iron double gate | PKR 60,000 - 200,000 |
| Wrought iron gate with ornament | PKR 55,000 - 150,000 |
| Steel plate used in a gate, per sq ft | PKR 1,800 - 2,500 |
| Gate latch with cylinder | PKR 1,500 - 5,000 |
| Electric gate lock, drop bolt or magnetic | PKR 8,000 - 30,000 |
Main gate design
A main gate faces the street, so it carries the look of the whole house. Most homeowners choose a double-leaf swing gate in iron or steel, 10 to 14 feet wide, framed by two pillars. Keep the leaf height between 5.5 and 7 feet, which blocks the view from the road without feeling like a wall. For wider plots, make the two leaves unequal so the smaller one can open alone for people. Match the gate colour to the window frames and the door, and see double door and gate pairings for combinations that work.
Steel and iron gate design
Steel gates use tubes, flat bar and sheet and give a clean, straight look. Wrought iron adds scrollwork, spears and curved tops, and suits older and classic houses. Choose a frame of at least 40 by 40 mm tube for a double gate, with a cross brace to stop sagging. Solid sheet cladding gives privacy, while vertical bars let light and air through. Both finish well in powder coat. Read the material notes in steel and iron doors and steel door design, since the same gauge and rust rules apply to gates.
Modern and simple gate design
Modern gates drop ornament for straight lines: horizontal slats, flat bar spacing, laser-cut sheet patterns and slim black frames. A simple gate is also cheaper, because less fabrication time goes into it. Wood-grain powder coat, composite slats and matt grey or black finishes are common choices. Keep the pattern the same on the gate and the walk-through leaf, and repeat one line from the gate on the boundary wall or railing so the front looks planned, not assembled.
Sliding gate design
A sliding gate suits plots with little front space, because it opens sideways instead of swinging out. A cantilever type hangs from a track box and leaves the ground clear, while a track type runs on a rail in the floor and collects dust. You need a clear wall length beside the opening about equal to the gate width. A motor and rack set is usually fitted with a remote, and the locking options are covered in electric gate lock. For indoor equivalents, see automatic sliding doors.
Walk-through and side gates
A walk-through gate lets people in without opening the car gate. Make it 3 to 3.5 feet wide, hang it on its own hinges, and give it a separate latch. Put it on the side of the wide gate that is nearer the house door. A spring closer keeps it from being left open, and the lock choices are in gate lock price in Pakistan.
Pillars, boundary wall and lighting
The pillar is half of the gate design. Brick, tile, stone cladding and plastered concrete all work, and the gate leaves should hang from steel posts cast into the pillar, not just fixed to the cladding. Leave a recess at the top of each pillar for a lamp, with the cable run in a conduit before the cladding goes on. Lamp options and rates are on gate pillar lights.
Finish, paint and rust
Rust starts at the bottom rail, where water collects. Use red oxide primer and two coats of enamel, or a powder coat, and seal the bottom edge. Touch up chips at once. Near the coast, use galvanised tube or stainless steel hardware. Repaint every three to four years in dust and rain, and grease the hinges every season so the gate does not drop.
Checks before you order
Measure the opening and the swing space before the design is chosen. Ask for tube size, sheet thickness, hinge type, finish and lock in writing, and compare quotes on the same scope. Look at the welds and the corners of a finished gate, and ask whether pillars and fitting are in the price. A gate that is slightly too wide can be corrected on paper, but not after it is made.
Frequently Asked Questions
A double-leaf iron or steel swing gate with a smaller walk-through leaf suits most houses. Choose vertical bars for airflow or solid sheet for privacy, and match the colour to the windows.
An iron double gate costs PKR 60,000 to 200,000 and a wrought iron gate with ornament PKR 55,000 to 150,000, depending on the size, the metal and the finish.
A sliding gate saves frontage and suits busy roads, but needs a clear wall length beside the opening. A swing gate is cheaper and simpler when you have room to open it.
A double gate is usually 10 to 14 feet wide and 5.5 to 7 feet high. Measure the opening and the car turning space before you finalise the design.
Use red oxide primer and enamel or powder coat, seal the bottom rail and touch up chips at once. Near the coast, use galvanised tube and stainless fittings.
Matt black, matt grey and wood-grain powder coat suit modern gates, with horizontal slats or laser-cut sheet. Keep one colour across the gate, the walk-through leaf and any railing.
Planning a gate?
Send the opening width, the plot photo and the style you like. We reply with a written rate.